Water Leaks and the waste of water associated with the leaks!

Water Leaks --- My last post explained the reasons behind leaks. What causes them and how to best protect your plumbing system from having them.

Today, I will speak on just how much water is wasted on various types of leaks.

The number one source of wasted water within the home or place of business is the toilet... Often overlooked and frequently procrastinated on. When a toilet leaks: it tends to be internal (leaking directly from the toilet tank into the bowl and down the drain) and as such, it doesn't cause any visible damage - resulting in the repair being pushed off to some other time... Down the drain goes our precious resource and your money. A leaky toilet wastes between 300 gallons (a slow leak) and 60,000 (constantly running toilet) per MONTH!

The best way to detect a leak besides visually seeing or hearing the leak - is to drop a little food coloring into the toilet tank and wait 10-15 minutes without flushing. If the water in the bowl turns color, your tank is leaking.

Leaking faucets can also increase your water bills!
 Slow Leaks - 450 gallons per month
 Steady Drips - 750 gallons per month
 Slow Stream - 3,000 gallons per month
 Steady Stream - 12,000 gallons per month

The Underground Leak / Under concrete slabs interior aka "slab leak" / Exterior Leaks / Pin Hole leaks
can leak at a rate of (per size of pinhole)
 1/32" leak - 3,600 gals/month
 1/16" leak - 10,800 gals/month
 1/8" leak - 36,000 gals/month
 3/16" leak - 199,000 gals/month
 1/4" leak - 340,000 gals/month

Underground Slab Leak

Leak on 1/2" copper fitting

Leak on 1/2" Type M copper pipe

Some Tell-Tale signs a leak exists...
- Water bill increase
- Gas bill increase (indicating a hot side leak)
- Hot spots on ground level floors
- Musty/Mildew smell!
- Water meter dial is rotating with no known use of water
- The constant sound of running water or a hissing noise with no known use of water.
- The sporadic sound of water running or what sounds like the toilet is filling up after its been flushed
- Luke warm or hot water coming out of the cold side tap.

The following metrics were based on the incoming water pressure being between 60-80 psi. The higher the incoming pressure the more waste...

Have a question? Comment below and I will do my best to answer - Thanks for taking a few moments to read my blog, by Anthony Pouliot with http://www.aap-allamericanplumbing.com/leak-detection/

What causes plumbing problems?

Plumbing, everybody fears the plumber... The high cost, the mess, the intrusion of ones personal space. The stress involved during a plumbing problem can be enormous! Water everywhere, sewage flowing out onto the floors or through the walls - MOLD! Ughh, mold and mildew.

Why do we hear of so many people having had some sort of plumbing disaster? LACK OF MAINTENANCE.... We take our cars for regular check ups. We check and protect our computers. We go to the doctors for our yearly physicals. But, we don't call a plumber until its absolutely necessary - usually, when the disaster is upon us.

How can one protect the home and wallet from a plumbing disaster? Simply put, with a little bit of preventive maintenance. You see, most of all plumbing problems fall into 1 of 4 categories.

1.High Incoming Water Pressure: What is the first thing your doctor checks upon seeing you? Your blood pressure. Why? Your blood pressure levels can directly affect your well being is so many ways. The same is true within your plumbing system. High water pressure (deemed as any pressure above 80psi) can and will destroy your plumbing system. http://www.watts.com/pages/learnAbout/reducingValves.asp?catId=64

2.Thermal Expansion: What is thermal expansion? The best way to describe thermal expansion is - water expands when heated. Similar to what occurs when boiling water in a tea pot. The expansion created by the steam blows the whistle. The same can occur within your plumbing system whenever the water heater is heating water and the expansion has no where to go. http://www.watts.com/pages/learnAbout/thermalExpansion.asp?catId=64#generalinfo_plumbingcode

3.Bad Water Quality: Those hard white spots and grime surrounding your faucets, sinks and shower doors aren't a good thing. If that sort of build up occurs within the surface of items that rarely have water on them; can you imagine what the inside of the pipes and water heater looks like? Hard water will most definitely lead to premature failure of your faucets, dishwasher, toilets and more.http://ga.water.usgs.gov/edu/waterquality.html

4. Poor workmanship: Poor workmanship, either by way of original construction and/or previous repairs made by handymen, weekend warriors, and the likes - to be inferior and not withstanding the local plumbing codes or better practices. It is always best to ensure good quality by way of requiring all work performed within your home or place of business be permitted with the local governing agency. Albeit, this will not ensure or absolve one from poor workmanship - it will definitely curb 95% of it. http://www.cslb.ca.gov/consumers/hireacontractor/BuildingPermitRequirements.asp

So what does all of this mean and what must one do to protect themselves from plumbing disasters?
1. Check the incoming water pressure yearly.
2. Check for Thermal Expansion
3. Invest in the appropriate water treatment device that best suits your locale
4. Maintain a level of security by requiring your plumber to secure permits on all of your projects

Visit our website for more information at www.aap-allamericanplumbing.com